Spectroscopy Setup

Dynamic range per capacitance (1.2.3)

• Procedures : FmIltProc/DynamicRangeSpectro

• Pre-test setup:
  • Note, that the related PTD contains a combined measurement of 1.2.3, 1.2.8 and 1.2.18 blocks, and cannot be applied in its original form.
  • Set the OGSE BB temperatures (SET_UP_OGSE_BB_TEMP_OBS, see the temperatures below)
  • Move filter wheel to "POS A" (SPEC_fltw_move)

• CUS scripts: SPEC_dyn_range_obs, SPEC_DiagHK_DynRange_block_stop, SPEC_DiagHK_DynRange_block_start

• Each measurement block (OGSE BB temperature setup) runs through all combinations of integration capacitor (0.1pF, 0.3pF, 1pF, 3pF) and reset interval values (1/8s, 1/4s, 1/2s, 2s), and is performed for two grating positions (GR-1 = 760000 and GR-2 = 490000).
  • Setup #1: OBSE BB1: 16.3K, OGSE BB2: 15.7K
  • Setup #2: OBSE BB1: 18.8K, OGSE BB2: 18.2K
  • Setup #3: OBSE BB1: 25.4K, OGSE BB2: 24.6K
  • Setup #4: OBSE BB1: 32.5K, OGSE BB2: 31.5K
  • Setup #5: OBSE BB1: 40.7K, OGSE BB2: 39.3K
  • Setup #6: OBSE BB1: 48.0K, OGSE BB2: 46.0K
  • Setup #7: OBSE BB1: 61.4K, OGSE BB2: 58.6K
  • Setup #8: OBSE BB1: 77.0K, OGSE BB2: 73.0K
• Estimated duration of the tests for each indivitual OGSE BB setting: 2x4x4x128s + 2x15s for grating movement + 1080s OGSE BB stabilization = 1.45h

Signal dependence on chopper frequency (1.2.8)

• Procedures : FmIltProc/DynamicRangeSpectro

• Pre-test setup:
  • CS1 temperature: 70.5K (fixed)
  • CS2 temperature: 76.0K (fixed)
  • Grating: 425250 (fixed)
  • Reset interval: 1/4s (fixed)
  • SPU setup: Entire slope fitting
  • Set the OGSE BB temperatures (SET_UP_OGSE_BB_TEMP_OBS, see the temperatures below)
  • Move filter wheel to "POS B" (SPEC_fltw_move)
• CUS script: SPEC_chopper_freq_fmilt128_obs

Edit conflict - other version:

• Each measurement block (OGSE BB temperature setup) runs performs a tringular chopping measurement between the calibration sources and the OGSE BB1 as OGSE BB1 -- CS1 -- OGSE BB1 -- CS2 -- OBSE BB1 -- CS1 -- ...

Edit conflict - your version:

• Each measurement block (OGSE BB temperature setup) performs a tringular chopping measurement between the calibration sources and the OGSE BB1 as OGSE BB1 --> CS1 --> OGSE BB1 --> CS2 --> OBSE BB1 --> CS1 --> ...

End of edit conflict

• Setup #1: OBSE BB1: 18.8K
• Setup #2: OBSE BB1: 25.4K
• Setup #3: OBSE BB1: 32.5K
• Setup #4: OBSE BB1: 40.7K
• Setup #5: OBSE BB1: 48.0K
• Setup #6: OBSE BB1: 61.4K ?
• Setup #7: OBSE BB1: 77.0K ?

• Estimated duration of the tests for each indivitual OGSE BB setting: ~0.45h

Time constants: flux changes, spectrometer (1.2.18)

• Procedures : FmIltProc/DynamicRangeSpectro

• Pre-test setup:
  • Grating: 425250 (fixed)
  • Reset interval: 1/4s (fixed)
  • Integration capacitor: should be adjusted according to 1.2.3
  • SPU setup: Entire slope fitting
  • Set the OGSE BB temperatures (SET_UP_OGSE_BB_TEMP_OBS, see the temperatures below)
  • Move filter wheel to "POS B" (SPEC_fltw_move)
  • Move chopper to CFOV
• CUS script: SPEC_time_constant_fmilt1218_obs
• Each measurement block (OGSE BB temperature setup) performs the following measurement: the detector is staring at the OGSE BB1 source, and the filter wheel is rotated back and forth.
  • Setup #1: OBSE BB1: 18.8K
  • Setup #2: OBSE BB1: 25.4K
  • Setup #3: OBSE BB1: 32.5K
  • Setup #4: OBSE BB1: 40.7K
  • Setup #5: OBSE BB1: 48.0K
  • Setup #6: OBSE BB1: 61.4K ?
  • Setup #7: OBSE BB1: 77.0K ?
• Estimated duration of the tests for each indivitual OGSE BB setting: ~0.25h, without OGSE BB stabilization.