Differences between revisions 1 and 22 (spanning 21 versions)

PACS bolometer operation from the commanding point of view

T. Mueller, D. Cesarsky; 08-Nov-2006

1. Short functional tests (PhFPU related)

1.1. SFT Warm: Sorption Cooler and Bolometer detector chain

PACS_Phot_SFT_Cooler_Warm_OBS, calling PACS_Phot_SFT_Cooler_Warm
PACS_Phot_DPU_DMC_Setup_OBS, calling PACS_Phot_DPU_DMC_Setup
PACS_Phot_Switchon_OBS, calling PACS_Phot_Switchon
PACS_Phot_Sequencer_Setup_OBS, calling PACS_Phot_Sequencer_Setup
PACS_Phot_SPU_Setup_OBS, calling PACS_Phot_SPU_Setup
PACS_Phot_Warm_Startinputsignal_OBS, calling PACS_Phot_Warm_Startinputsignal (Duration: 637 sec)
PACS_Phot_SPU_Reset_OBS, calling PACS_Phot_SPU_Reset
PACS_Phot_Switchoff_OBS, calling PACS_Phot_Switchoff

Note: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)

1.2. SFT at HeI: Sorption Cooler and Bolometer detector chain

PACS_Phot_SFT_Cooler_OBS, calling PACS_Phot_SFT_Cooler
PACS_Phot_DPU_DMC_Setup_OBS, calling PACS_Phot_DPU_DMC_Setup
PACS_Phot_Switchon_OBS, calling PACS_Phot_Switchon
PACS_Phot_Sequencer_Setup_OBS, calling PACS_Phot_Sequencer_Setup
PACS_Phot_SPU_Setup_OBS, calling PACS_Phot_SPU_Setup
PACS_Phot_Cold_Startinputsignal_OBS, calling PACS_Phot_Cold_Startinputsignal (Duration: 637 sec)
PACS_Phot_SPU_Reset_OBS, calling PACS_Phot_SPU_Reset
PACS_Phot_Switchoff_OBS, calling PACS_Phot_Switchoff

Note: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)

1.3. SFT at HeII (cooler not recycled): Sorption Cooler and Bolometer detector chain

PACS_Phot_SFT_Cooler_OBS, calling PACS_Phot_SFT_Cooler
PACS_Phot_DPU_DMC_Setup_OBS, calling PACS_Phot_DPU_DMC_Setup
PACS_Phot_Switchon_OBS, calling PACS_Phot_Switchon
PACS_Phot_Sequencer_Setup_OBS, calling PACS_Phot_Sequencer_Setup
PACS_Phot_SPU_Setup_OBS, calling PACS_Phot_SPU_Setup
PACS_Phot_Cold_Startinputsignal_OBS, calling PACS_Phot_Cold_Startinputsignal (Duration: 637 sec)BR
PACS_Phot_SPU_Reset_OBS, calling PACS_Phot_SPU_Reset
PACS_Phot_Switchoff_OBS, calling PACS_Phot_Switchoff

Note: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)

2. Nominal operations

2.1. Instrument switch-on and connection of the warm electronic boxes

currently done with tcl-script PACS_Switch_On.tcl (maintained by FGB)
after execution: PACS is in SAFE mode, the bolometer groups are off, but the temperature sensors are on

Note: Autonomy function #6 is enabled to check for the communication between DMC and BOLC

2.2. Cooler recycling (only at HeII temperatures)

starting out of SAFE mode (groups off, temperature sensors on)
mode BOLO_cooler_OBS calling the CUS procedure BOLO_cool_recycle:
- no sub-procedures are called, the groups and temperature sensors are not touched
- HK_list is set to PHOT_HK and reset to "NON-PRIME" in the end
- autonomy function 14 is enabled, Duration: 7928 sec
ending up in SAFE mode (groups are off, temperature sensors on, HSP heater current at 1.18 mA)

Note: At the end of the recycling the autonomy function 14 is enabled. It checks for TEMP_EV, TEMP_FPU1, TEMP_FPU2: --> HK DEC SOFT is generated if one or more are out of the range [260,320] mK; --> GO SAFE is generated if one or more are above 400 mK

2.3. General Setup for Photometer Operation (after cooler recycling)

starting out of SAFE mode (groups off, temperature sensors on)
mode PHOT_setup_OBS calling the block PHOT_setup, calling the following CUS procedures:
- procedure PHOT_dpu_dmc_setup
- procedure PHOT_dmc_setup
  - procedure PHOT_fltw_conf
  - procedure CONF_chopper
  - procedure CONF_cs
- procedure PHOT_switchon_groups
- procedure PHOT_set_bias (*)
- procedure PHOT_seq_setup
- procedure PHOT_change_data_mode
- procedure PHOT_change_seq_mode
- procedure PHOT_set_gain
- procedure PHOT_spu_setup
  - (*) the bias tables to be loaded can change!
ending up in Photometry mode, but SPU processing has not yet started
filter is in position "A", chopper at position "0"
calibration sources are set to default values, but need 40-50 min stabilisation time!!!

Note 1: At the end of the PHOT_setup_OBS the autonomy function 17 "generate_event_pwr" is enabled. It checks for the HK entries: PC_PWR_ANA_P_#, PC_PWR_ANA_N_# and PC_PWR_DIG_#, with # = [1,2,3,4,5,6,7]

Note 2: PHOT_setup_OBS can be called via the generic tcl-script (with a default bias table) or via a specific tcl-script together with a special bias table.

2.4. Operation of the bolometers (starting out of '''Photometry mode''')

2.4.1. start/stop of bolometer data flow

mode PHOT_spu_setup_OBS calling procedure PHOT_spu_setup ---> bolometer data flow running
mode PHOT_spu_reset_OBS calling procedure PHOT_spu_reset ---> bolometer data flow stopped

2.4.2. Change of the bolometer data/sequence mode and gain

procedure PHOT_change_data_mode
procedure PHOT_change_seq_mode
procedure PHOT_set_gain
or via MSTK with individual commands

2.4.3. Take data with manual chopper & filter movements

mode PHOT_spu_setup_OBS calling procedure PHOT_spu_setup ---> bolometer data flow running
- mode PACS_fltw_move_OBS calling procedure PHOT_fltw_move (or SPEC_fltw_move)
- or command Pacs_DMC_MOVE_CHOP_ABS
- or command Pacs_DMC_MOVE_CHOP_REL
mode PHOT_spu_reset_OBS calling procedure PHOT_spu_reset ---> bolometer data flow stopped

Note: PACS_fltw_move_OBS can be called via a specific tcl-script where the filter has to be specified.

2.4.4. Take data with pre-defined OBCPs

mode OBCP_chopped_photometry_OBS calling blocks/procedures:
- procedure PHOT_spu_setup
- procedure PHOT_fltw_move
- block OBCP_chopped_photometry
- procedure PHOT_fltw_move
- block OBCP_chopped_photometry
- procedure PHOT_fltw_move
- procedure PHOT_spu_reset
mode OBCP_phot_chopper_scan_OBS calling blocks/procedures:
- procedure PHOT_spu_setup
- procedure PHOT_fltw_move
- block OBCP_phot_chopper_scan
- procedure PHOT_fltw_move
- block OBCP_phot_chopper_scan
- procedure PHOT_fltw_move
- procedure PHOT_spu_reset
mode OBCP_fixed_fixed_photo_OBS calling blocks/procedures:
- procedure PHOT_spu_setup
- procedure PHOT_fltw_move
- block OBCP_fixed_fixed_photo
- procedure PHOT_fltw_move
- block OBCP_fixed_fixed_photo
- procedure PHOT_fltw_move
- procedure PHOT_spu_reset
mode PHOT_all_aots_OBS calling the following blocks/procedures:
- procedure PHOT_spu_setup
- procedure PHOT_fltw_move
- block OBCP_chopped_photometry
- block OBCP_chopped_photometry_dither
- block OBCP_phot_freezeframe
- block OBCP_phot_cal_I
- block OBCP_phot_cal_II
- block OBCP_phot_cal_III
- block OBCP_phot_staring
- block OBCP_phot_chopper_scan
- block OBCP_fixed_fixed_photo
- procedure PHOT_fltw_move
- block OBCP_chopped_photometry
- block OBCP_chopped_photometry_dither
- block OBCP_phot_freezeframe
- block OBCP_phot_cal_I
- block OBCP_phot_cal_II
- block OBCP_phot_cal_III
- block OBCP_phot_staring
- block OBCP_phot_chopper_scan
- block OBCP_fixed_fixed_photo
- procedure PHOT_fltw_move
- procedure PHOT_spu_reset

Note: all these modes can be started with default parameters via the generic tcl-script; the three key-OBCPs can also be started with freely selectable parameters via specific tcl-scripts

2.4.5. Execute AOT observations

CUS scripts (to be finalised):BR
- PHOT_AOTBR
  - - PacsPhotDefaults BR - PacsPhotEstimatorOBCPnBR
    - - PacsDureeOBCP5BR
      - - DMC_phot_2_3_chopBR
      - PacsDureeOBCP7BR
      - - DMC_staring_photBR
    Logic chooses and issues a pointing mode out of:BR
    - - composite_noddingBR - repeated_raster_with_holdBR - line_scan_with_holdBR
    - WriteOBSIDBR - PacsPhotSlewCal BR
    - - PHOT_aot_prologueBR
      - - PHOT_spu_setupBR
      - PHOT_fltw_moveBR - OBCP_chopped_photometryBR
    - PacsPhotCommandOBCP7BR
    - - OBCP_staring_photometryBR
    - PacsPhotCommandOBCP5BR
    - - OBCP_chopped_photometry_ditherBR
    - PHOT_aot_epilogueBR - WriteEndIDBR - PacsPhotNoiseRMSBR - PacsMessageCenter BR

Note: the default OBCP for point-source photometry will probably be the OBCP_fixed_fixed_photo.

2.5. Reset after photometer operation

PACS is in PHOTOMETRY or any other mode
execute mode PHOT_switchoff_groups_OBS calling procedure PHOT_switchoff_groups (this will reset the biases sequentially, disable the AF 17, and switch off the groups)
going into SAFE mode (this will disable the AF 14 for the FPU temperature checks)
after execution: PACS is in SAFE mode (groups are off, temperature sensors on, AF 6 enabled to check for the communication between DMC and BOLC)

2.6. Instrument switch-off

currently done with the tcl-script PACS_Switch_Off.tcl (maintained by FGB) (this will disable the AF 6 for the DMC-BOLC communication check)
after execution: PACS is switched off

3. NOTES

the SFT tests are described in PACS-ME-TP-007
some specific photometer tests, like the thermal behaviour measurements, start directly out of SAFE mode, while most of the tests will be executed after the PHOT_setup when the instrument is in Photometry mode
the above mentioned CUS scripts (with a few exceptions) have been tested and are available in the CUS database and from the CVS library
the AOT related CUS-scripts are still under testing

Herschel: PACS/FM_ILT_Procedures/PhotOperations (last edited 2009-07-15 14:32:37 by localhost)

-  ⇤ ← Revision 1 as of 2006-07-14 08:04:53 → 
  Size: 6315
  Editor: kleinplanet
  Comment:
+   ← Revision 22 as of 2006-11-09 13:09:08 → ⇥
  Size: 11732
  Editor: ThomasMueller
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
-= PACS bolometer operation from the commanding point of view =
+#pragma section-numbers on
'''Index'''
[[TableOfContents(2)]]

'''PACS bolometer operation from the commanding point of view'''
-Line 4:
+Line 8:
-T. Mueller, D. Cesarsky
19-May-2006
+T. Mueller, D. Cesarsky;
08-Nov-2006

------------------------------------------------------------------------------------
= Short functional tests (PhFPU related) =
------------------------------------------------------------------------------------


== SFT Warm: Sorption Cooler and Bolometer detector chain ==

 * '''PACS_Phot_SFT_Cooler_Warm_OBS''', calling '''PACS_Phot_SFT_Cooler_Warm'''

 * '''PACS_Phot_DPU_DMC_Setup_OBS''', calling '''PACS_Phot_DPU_DMC_Setup'''
 * '''PACS_Phot_Switchon_OBS''', calling '''PACS_Phot_Switchon'''
 * '''PACS_Phot_Sequencer_Setup_OBS''', calling '''PACS_Phot_Sequencer_Setup'''
 * '''PACS_Phot_SPU_Setup_OBS''', calling '''PACS_Phot_SPU_Setup'''
 * '''PACS_Phot_Warm_Startinputsignal_OBS''', calling '''PACS_Phot_Warm_Startinputsignal''' (Duration: 637 sec)
 * '''PACS_Phot_SPU_Reset_OBS''', calling '''PACS_Phot_SPU_Reset'''
 * '''PACS_Phot_Switchoff_OBS''', calling '''PACS_Phot_Switchoff'''

__Note__: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)


== SFT at HeI: Sorption Cooler and Bolometer detector chain ==

 * '''PACS_Phot_SFT_Cooler_OBS''', calling '''PACS_Phot_SFT_Cooler'''

 * '''PACS_Phot_DPU_DMC_Setup_OBS''', calling '''PACS_Phot_DPU_DMC_Setup'''
 * '''PACS_Phot_Switchon_OBS''', calling '''PACS_Phot_Switchon'''
 * '''PACS_Phot_Sequencer_Setup_OBS''', calling '''PACS_Phot_Sequencer_Setup'''
 * '''PACS_Phot_SPU_Setup_OBS''', calling '''PACS_Phot_SPU_Setup'''
 * '''PACS_Phot_Cold_Startinputsignal_OBS''', calling '''PACS_Phot_Cold_Startinputsignal''' (Duration: 637 sec)
 * '''PACS_Phot_SPU_Reset_OBS''', calling '''PACS_Phot_SPU_Reset'''
 * '''PACS_Phot_Switchoff_OBS''', calling '''PACS_Phot_Switchoff'''

__Note__: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)


== SFT at HeII (cooler not recycled): Sorption Cooler and Bolometer detector chain ==

 * '''PACS_Phot_SFT_Cooler_OBS''', calling '''PACS_Phot_SFT_Cooler'''

 * '''PACS_Phot_DPU_DMC_Setup_OBS''', calling '''PACS_Phot_DPU_DMC_Setup'''
 * '''PACS_Phot_Switchon_OBS''', calling '''PACS_Phot_Switchon'''
 * '''PACS_Phot_Sequencer_Setup_OBS''', calling '''PACS_Phot_Sequencer_Setup'''
 * '''PACS_Phot_SPU_Setup_OBS''', calling '''PACS_Phot_SPU_Setup'''
 * '''PACS_Phot_Cold_Startinputsignal_OBS''', calling '''PACS_Phot_Cold_Startinputsignal''' (Duration: 637 sec)[[BR]]
 * '''PACS_Phot_SPU_Reset_OBS''', calling '''PACS_Phot_SPU_Reset'''
 * '''PACS_Phot_Switchoff_OBS''', calling '''PACS_Phot_Switchoff'''

__Note__: No specific autonomy functions are involved here (except AF#6 to check for the communication between DMC and BOLC)

------------------------------------------------------------------------------------
= Nominal operations =
------------------------------------------------------------------------------------


== Instrument switch-on and connection of the warm electronic boxes ==

 * currently done with tcl-script '''PACS_Switch_On.tcl''' (maintained by FGB)
 * after execution: PACS is in '''SAFE mode''', the bolometer groups are off, but the temperature sensors are on

__Note__: Autonomy function #6 is enabled to check for the communication between DMC and BOLC



== Cooler recycling (only at HeII temperatures) ==

 * starting out of '''SAFE mode''' (groups off, temperature sensors on)
 * mode '''BOLO_cooler_OBS''' calling the CUS procedure '''BOLO_cool_recycle''':
   * no sub-procedures are called, the groups and temperature sensors are not touched
   * HK_list is set to PHOT_HK and reset to "NON-PRIME" in the end
   * autonomy function 14 is enabled, Duration: 7928 sec
 * ending up in '''SAFE mode''' (groups are off, temperature sensors on, HSP heater current at 1.18 mA)

__Note__: At the end of the recycling the autonomy function 14 is enabled. It checks for TEMP_EV, TEMP_FPU1, TEMP_FPU2: --> HK DEC SOFT is generated if one or more are out of the range [260,320] mK; --> GO SAFE is generated if one or more are above 400 mK
   


== General Setup for Photometer Operation (after cooler recycling) ==

 * starting out of '''SAFE mode''' (groups off, temperature sensors on)
 * mode '''PHOT_setup_OBS''' calling the block '''PHOT_setup''', calling the following CUS procedures:
   * procedure  PHOT_dpu_dmc_setup
   * procedure  PHOT_dmc_setup
     * procedure  PHOT_fltw_conf
     * procedure  CONF_chopper
     * procedure  CONF_cs
   * procedure  PHOT_switchon_groups
   * procedure  PHOT_set_bias (*)
   * procedure  PHOT_seq_setup
   * procedure  PHOT_change_data_mode
   * procedure  PHOT_change_seq_mode
   * procedure  PHOT_set_gain
   * procedure  PHOT_spu_setup
    (*) the bias tables to be loaded can change!

 * ending up in '''Photometry mode''', but SPU processing has not yet started
 * filter is in position "A", chopper at position "0"
 * calibration sources are set to default values, but need 40-50 min stabilisation time!!!

__Note 1__: At the end of the '''PHOT_setup_OBS''' the autonomy function 17 "generate_event_pwr" is enabled. It checks for the HK entries: PC_PWR_ANA_P_#, PC_PWR_ANA_N_# and PC_PWR_DIG_#, with # = [1,2,3,4,5,6,7]

__Note 2__: '''PHOT_setup_OBS''' can be called via the generic tcl-script (with a default bias table) or via a specific tcl-script together with a special bias table.
 

== Operation of the bolometers (starting out of '''Photometry mode''') ==


=== start/stop of bolometer data flow ===
 * mode '''PHOT_spu_setup_OBS''' calling procedure '''PHOT_spu_setup''' --->  bolometer data flow running
 * mode '''PHOT_spu_reset_OBS''' calling procedure '''PHOT_spu_reset''' --->  bolometer data flow stopped


=== Change of the bolometer data/sequence mode and gain ===
 * procedure  '''PHOT_change_data_mode'''
 * procedure  '''PHOT_change_seq_mode'''
 * procedure  '''PHOT_set_gain'''

 * or via MSTK with individual commands


=== Take data with manual chopper & filter movements ===
 * mode '''PHOT_spu_setup_OBS''' calling procedure '''PHOT_spu_setup''' --->  bolometer data flow running
   * mode '''PACS_fltw_move_OBS''' calling procedure '''PHOT_fltw_move''' (or '''SPEC_fltw_move''')
   * or command  '''Pacs_DMC_MOVE_CHOP_ABS'''
   * or command  '''Pacs_DMC_MOVE_CHOP_REL'''
 * mode '''PHOT_spu_reset_OBS''' calling procedure '''PHOT_spu_reset''' --->  bolometer data flow stopped

__Note__: '''PACS_fltw_move_OBS''' can be called via a specific tcl-script where the filter has to be specified.

=== Take data with pre-defined OBCPs ===
 * mode '''OBCP_chopped_photometry_OBS''' calling blocks/procedures:
   * procedure '''PHOT_spu_setup'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_chopped_photometry'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_chopped_photometry'''
   * procedure '''PHOT_fltw_move'''
   * procedure '''PHOT_spu_reset'''

 * mode '''OBCP_phot_chopper_scan_OBS''' calling blocks/procedures:
   * procedure '''PHOT_spu_setup'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_phot_chopper_scan'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_phot_chopper_scan'''
   * procedure '''PHOT_fltw_move'''
   * procedure '''PHOT_spu_reset'''

 * mode '''OBCP_fixed_fixed_photo_OBS''' calling blocks/procedures:
   * procedure '''PHOT_spu_setup'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_fixed_fixed_photo'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_fixed_fixed_photo'''
   * procedure '''PHOT_fltw_move'''
   * procedure '''PHOT_spu_reset'''

 * mode '''PHOT_all_aots_OBS''' calling the following blocks/procedures:
   * procedure '''PHOT_spu_setup'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_chopped_photometry'''
   * block '''OBCP_chopped_photometry_dither'''
   * block '''OBCP_phot_freezeframe'''
   * block '''OBCP_phot_cal_I'''
   * block '''OBCP_phot_cal_II'''
   * block '''OBCP_phot_cal_III'''
   * block '''OBCP_phot_staring'''
   * block '''OBCP_phot_chopper_scan'''
   * block '''OBCP_fixed_fixed_photo'''
   * procedure '''PHOT_fltw_move'''
   * block '''OBCP_chopped_photometry'''
   * block '''OBCP_chopped_photometry_dither'''
   * block '''OBCP_phot_freezeframe'''
   * block '''OBCP_phot_cal_I'''
   * block '''OBCP_phot_cal_II'''
   * block '''OBCP_phot_cal_III'''
   * block '''OBCP_phot_staring'''
   * block '''OBCP_phot_chopper_scan'''
   * block '''OBCP_fixed_fixed_photo'''
   * procedure '''PHOT_fltw_move'''
   * procedure '''PHOT_spu_reset'''

__Note__: all these modes can be started with default parameters via the generic tcl-script; the three key-OBCPs can also be started with freely selectable parameters via specific tcl-scripts

=== Execute AOT observations ===
        CUS scripts (to be finalised):[[BR]]

            PHOT_AOT[[BR]]
               - PacsPhotDefaults[[BR]]
               - PacsPhotEstimatorOBCPn[[BR]]
                  - PacsDureeOBCP5[[BR]]
                     - DMC_phot_2_3_chop[[BR]]
                  - PacsDureeOBCP7[[BR]]
                     - DMC_staring_phot[[BR]]
               Logic chooses and issues a pointing mode out of:[[BR]]
                  - composite_nodding[[BR]]
                  - repeated_raster_with_hold[[BR]]
                  - line_scan_with_hold[[BR]]
               - WriteOBSID[[BR]]
               - PacsPhotSlewCal[[BR]]
                  - PHOT_aot_prologue[[BR]]
                     - PHOT_spu_setup[[BR]]
                  - PHOT_fltw_move[[BR]]
                  - OBCP_chopped_photometry[[BR]]
               - PacsPhotCommandOBCP7[[BR]]
                  - OBCP_staring_photometry[[BR]]
               - PacsPhotCommandOBCP5[[BR]]
                  - OBCP_chopped_photometry_dither[[BR]]
               - PHOT_aot_epilogue[[BR]]
               - WriteEndID[[BR]]
               - PacsPhotNoiseRMS[[BR]]
               - PacsMessageCenter[[BR]]

__Note__: the default OBCP for point-source photometry will probably be the OBCP_fixed_fixed_photo.


== Reset after photometer operation ==

 * PACS is in '''PHOTOMETRY''' or any other mode
 * execute mode '''PHOT_switchoff_groups_OBS''' calling procedure '''PHOT_switchoff_groups''' (this will reset the biases sequentially, disable the AF 17, and switch off the groups)
 * going into '''SAFE mode''' (this will disable the AF 14 for the FPU temperature checks)  
 * after execution: PACS is in '''SAFE mode''' (groups are off, temperature sensors on, AF 6 enabled to check for the communication between DMC and BOLC)



== Instrument switch-off ==

 * currently done with the tcl-script '''PACS_Switch_Off.tcl''' (maintained by FGB) (this will disable the AF 6 for the DMC-BOLC communication check)
 * after execution: PACS is switched off
-Line 9:
+Line 242:
-. Instrument switch-on and connection of the warm electronic boxes
+= NOTES =
-Line 11:
+Line 244:
-  - currently done with tcl-script "PACS_Switch_On.tcl" (maintained by FGB):
  - after execution: PACS is in SAFE mode


------------------------------------------------------------------------
 2. Cooler recycling (only at HeII temperatures)
------------------------------------------------------------------------
  - starting out of SAFE mode
  - CUS script:  BOLO_cool_recycle
                 (no sub-procedures are called)
  - ending up in SAFE mode


------------------------------------------------------------------------
 3. General Setup for Photometer Operation
     (at warm, HeI, HeII temperatures and after cooler recycling)
------------------------------------------------------------------------
  - starting out of SAFE mode
  - CUS script:
        block  PHOT_setup  calling the following CUS procedures
    (will be renamed to PHOT_orbit_prologue):
               - procedure  PHOT_dpu_dmc_setup
               - procedure  PHOT_dmc_setup
                              - procedure  PHOT_fltw_conf (*)
                              - procedure  CONF_chopper (*)
                              - procedure  CONF_cs (*)
               - procedure  PHOT_set_bias (*)
               - procedure  PHOT_seq_setup
               - procedure  PHOT_change_data_mode
               - procedure  PHOT_change_seq_mode
               - procedure  PHOT_set_gain
               - procedure  PHOT_spu_setup
    (*) certain parameter values depend on the temperature
        environment!

  - ending up in PHOTOMETRY mode, but SPU processing has not yet
    started. Note: filter is in position "A", chopper at position "0",
    calibration sources are set to default values, but need 30-40 min
    stabilisation time!!!


------------------------------------------------------------------------
 4. Operation of the bolometers (starting out of PHOTOMETRY mode)
------------------------------------------------------------------------

     A) start/stop of bolometer data flow
        CUS scripts:
               - procedure  PHOT_spu_setup
             --->  bolometer data flow running
               - procedure  PHOT_spu_reset


     B) Change of the bolometer data/sequence mode and gain
        CUS scripts:
               - procedure  PHOT_change_data_mode
               - procedure  PHOT_change_seq_mode
               - procedure  PHOT_set_gain


     C) Take data with manual chopper & filter movements
        CUS scripts:
               - procedure  PHOT_spu_setup
             --->  bolometer data flow running
                   - procedure  PHOT_fltw_move
                   - command  Pacs_DMC_MOVE_CHOP_ABS
                   - command  Pacs_DMC_MOVE_CHOP_REL
               - procedure  PHOT_spu_reset


     D) Take data with pre-defined OBCPs
        CUS scripts:
               - procedure  PHOT_spu_setup
             --->  bolometer data flow running
                       - block  OBCP_chopped_photometry
                       - block  OBCP_chopped_photometry_dither
                       - block  OBCP_phot_freezeframe
                       - block  OBCP_phot_cal_I
                       - block  OBCP_phot_cal_II
                       - block  OBCP_phot_cal_III
                       - block  OBCP_phot_staring
                       - block  OBCP_phot_chopper_scan
                        (not yet available!!!)
                   - block  PHOT_all_aots_OBS
               - procedure  PHOT_spu_reset


     E) Execute AOT observations
        CUS scripts (to be finalised):

            PHOT_AOT
               - PacsPhotDefaults
               - PacsPhotEstimatorOBCPn
                  - PacsDureeOBCP5
                     - DMC_phot_2_3_chop
                  - PacsDureeOBCP7
                     - DMC_staring_phot
               Logic chooses and issues a pointing mode out of:
                  - composite_nodding
                  - repeated_raster_with_hold
                  - line_scan_with_hold
               - WriteOBSID
               - PacsPhotSlewCal
                  - PHOT_aot_prologue
                     - PHOT_spu_setup
                  - PHOT_fltw_move
                  - OBCP_chopped_photometry
               - PacsPhotCommandOBCP7
                  - OBCP_staring_photometry
               - PacsPhotCommandOBCP5
                  - OBCP_chopped_photometry_dither
               - PHOT_aot_epilogue
               - WriteEndID
               - PacsPhotNoiseRMS
               - PacsMessageCenter


------------------------------------------------------------------------
 5. Reset after photometer operation
------------------------------------------------------------------------
  - PACS is in PHOTOMETRY or any other mode
  - going into SAFE mode:
        CUS scripts:
               - block  OBCP_SAFE

  - after execution: PACS is in SAFE mode


------------------------------------------------------------------------
 6. Instrument switch-off
------------------------------------------------------------------------
  - currently done with a dedicated tcl-script (maintained by FGB)
  - after execution: PACS is switched off


------------------------------------------------------------------------
 7. NOTES
------------------------------------------------------------------------
  - there are more CUS scripts related to the SFT warm, HeI and HeII
    which are not mentioned here (see PACS-ME-TP-007)
  - some specific photometer tests, like the thermal behaviour
    measurements, start directly out of SAFE mode, while most
    of the tests will be executed after the "PHOT_setup"
  - the above mentioned CUS scripts (with a few exceptions) have been
    tested and are available in the CUS database and from the
    CVS library
  - the AOT related CUS-scripts are still under testing
+ * the SFT tests are described in PACS-ME-TP-007
 * some specific photometer tests, like the thermal behaviour measurements, start directly out of '''SAFE mode''', while most of the tests will be executed after the '''PHOT_setup''' when the instrument is in '''Photometry mode'''
 * the above mentioned CUS scripts (with a few exceptions) have been tested and are available in the CUS database and from the CVS library
 * the AOT related CUS-scripts are still under testing

Herschel: Diff for "PACS/FM_ILT_Procedures/PhotOperations"

1. Short functional tests (PhFPU related)

1.1. SFT Warm: Sorption Cooler and Bolometer detector chain

1.2. SFT at HeI: Sorption Cooler and Bolometer detector chain

1.3. SFT at HeII (cooler not recycled): Sorption Cooler and Bolometer detector chain

2. Nominal operations

2.1. Instrument switch-on and connection of the warm electronic boxes

2.2. Cooler recycling (only at HeII temperatures)

2.3. General Setup for Photometer Operation (after cooler recycling)

2.4. Operation of the bolometers (starting out of '''Photometry mode''')

2.4.1. start/stop of bolometer data flow

2.4.2. Change of the bolometer data/sequence mode and gain

2.4.3. Take data with manual chopper & filter movements

2.4.4. Take data with pre-defined OBCPs

2.4.5. Execute AOT observations

2.5. Reset after photometer operation

2.6. Instrument switch-off

3. NOTES